niedzial1983

3.2 is very nice. I have 3.0tdi and i love it but if i would be buying the car again i would go for 3.2 petrol or more.... 🙂

What wheel is that ? 18"?

That looks low...

Post a pic from the side so we can see how it looks like . On sline you will have sport suspention -30 . I belive the shocks are shorter than the standard

Hey. So how many we have for this ? With a bit of luck ill be there as well . What zone is our stand ?

Get a mobile sprayer booked , it should not be more than £150 to blend in

Pre-facelift Cars - 04 - 08 plate 1. Confirmation on Lock [Select] [46 - Central Conv] Coding - 07] +2048 to your existing coding (example - original code is 0008443 + 2048 = 0010491) [Do it!] 2. MMI High Hidden Menu [Select] [07 - Control Head] [Adaption - 10] Drop-down Menu [Select - Service Menu] Change 'New Value'to 1 [Test] [Save] Drop-down Menu [Select - MMI System Retstart] Change 'New Value' to 1 [Test] [Save] *MMI will now restart* [Done, Go Back] 3. Battery Meter After MMI restart and Hidden Menu enable - press Radio then hold in Setup + Car for a few seconds (it might take a few times to get timing correct) [Select] DIAG SETTINGS [Select] Car Menus Maske [Select] Battery Level Scroll to Accept Changes Press RETURN 3 times Restart MMI using Setup + MMI Control Knob + Upper Left Inner Key - release 4. Visual Parking Aid - if supported [Select] [76 - Park Assist] [Coding - 07] Change second digit to '2' Example - Original code is 0001106 ... New code is 0201106 [Do it!] Restart MMI and select reverse 5. Passenger Mirror Dip on Reverse - if supported [Select] [52 - Door Elec Pass.] [07 - Coding] Add +128 to original coding Example - original code is 0002682 ... New code is 0002810 [Do it!] Select LHS mirror on control and select reverse - mirror will dip if correct hardware is fitted 6. MMI High Startup Screen [Select] [07 - Control Head] [07- Coding] Look for the 3rd digit and change this to your preference as below xx0xxxx = A6 xx1xxxx = S6 xx3xxxx = RS6 [Do it!] Now go into: [10 - Adaption] Drop-down Menu [Select - MMI System Retstart] Change 'New Value' to 1 [Test] [Save] *MMI will now restart* [Done, Go Back] 7. Disable Seatbelt Warning [Select] [17 - Instrument Cluster] [07 - Coding] Look for the 6th digit and change this to your preference as below xxxxx0x = No Seatbelt Warning xxxxx1x = Seatbelt Warning (EU-NCAP) xxxxx2x = Seatbelt Warning (NAR Old) xxxxx3x = Seatbelt Warning (NAR New) xxxxx4x = Seatbelt Warning (EU-NCAP incl. Passenger) xxxxx5x = Seatbelt warning (NAR Old incl. Passenger) xxxxx6x = Seatbelt Warning (NAR New incl. Passenger) [Do it!] Turn ignition off and on NB . 2, 3, 5 & 6 are related to North America. 8. Bluetooth Module Voice Control - If your BT module supports this change [Select] [77 - Telephone] [07 - Coding] Look for the 6th digit in your current coding and change this to your prefered voice language 00x0x00 = Voice Control Off 00x0x10 = German 00x0x20 = English (UK) 00x0x30 = French 00x0x40 = Italian 00x0x50 = Spanish 00x0x60 = Spanish (USA) 00x0x70 = English (USA) 00x0x80 = French (Canada) 00x0x90 = Speaker dependant voice selection [Do it!] Now restart your MMI [Select] [07 - Control Head] [10 - Adaption] Drop-down Menu [Select - MMI System Retstart] Change 'New Value' to 1 [Test] [Save] *MMI will now restart* [Done, Go Back] 9 - Scandanavian DRL (rear tail lights on with front DRL) [Select] [09 - Cent Conv] [Coding - 07] Change the last digit in the coding string to '2' Example - 0xxxxx2 [Do It!] 10. Changing radio source by pressing RADIO [Select] [07 - Control Head] [Adaption - 10] Additional MMI Options Add 4 to your existing code (Frequency/Source Change via Function Button Active) [Test] [Save] ---------------------------------------------------------------- Facelift Cars - '58 plate onwards 1. Enabling Gauge Test/Needle Sweep [Select] [17 - Instruments] [Coding - 07] [Long Coding Helper] Click on the second byte in the list. Check the box for "Gauge Test/Needle Sweep active" [Do It!] 2. Hidden menu in 3G MMI [Select] [5F - Information Electr.] [Adaptation - 10] Choose Channel 6 change value from 0 to 1 [Save] [Done] 3. Enabling VIM (Video in Motion) [Select] [Control Module 5f] [Advanced ID - 1A] Make a note of the serial number and decode using MMI VIMGen [Security Access - 16] Enter the code generated above [Do it!] [Adaptation - 10] Choose Channel 48 change value from 0 to 255 [Save] [Done] Restart MMI 4. Enable Battery Meter once #2 has been completed Hold in CAR + SETUP car carextdevicelist check "Battery" return carmenuoperation set "Battery" to 5 return Restart MMI 5. Enable Bluetooth on MMI 3G [Select] [Control Module 5f] [Adaption - 10] Channel 06 New Value = 1 Test, Save, Done. Now go into the Hidden Menu, see 2. Hidden menu in 3G MMI Diagnose>Settings>Tel Settings Misc Change the available options to - [no WLAN/no NAD/BT/HFP] 4/16 Restart MMI (Hold in SETUP + Centre MMI Knob + Upper Right Inner Key] [Select] [Control Module 5F] [Adaption - 10] Channel 17 New Value = 1 Test, Save, Done. Restart MMI (Hold in SETUP + Centre MMI Knob + Upper Right Inner Key] If you have Nav fitted, the microphone will be present, if no Nav is fitted then you need to purchase microphone pack 4L1 (or 4L2) 035 711 G 6. Enable AMI (Audi Music Interface) on MMI 3G (after fitting the hardware) [Select] [Control Module 5F] [Adaption - 10] Channel 6 New Value = 1 Restart MMI (Hold in SETUP + Centre MMI Knob + Upper Right Inner Key] Go into hidden menu, hold in CAR + SETUP ... WARNING DO NOT CHANGE ANY VALUES YOU DON'T KNOW OR ELSE BAD BAD THINGS MAY HAPPEN 😉 Diagnosis -> Settings -> Audi Music Interface (AMI) set to 7/8 Press RETURN and come out of the hidden menu. Restart MMI (Hold in SETUP + Centre MMI Knob + Upper Right Inner Key] Press MEDIA, Source and test the AMI. 7. Visual Parking Aid - if supported [Select] [76 - Park Assist] [Coding - 07] Change second digit to '2' Example - Original code is 0001106 ... New code is 0201106 [Do it!] Restart MMI and select reverse 8. Enabling Lap Timer/Boost Guage/Oil Temp [Select] [17 - Instruments] [Coding - 07] [Long Coding Helper] Check the box for "Lap Timer active" [Do It!] 9. Enable Rear DRL (Scandinavian Lights) [Select] [09 - Cent Elec] [Coding - 07] Change the 7th digit (ie the last one) to 2 [Do It!] 10. Enable Passenger Mirror Dipping [Select] [52 - Passenger Door] [Coding - 07] Byte 4, bit 3 - Position memory for reverse gear dipping active Tick the box [Do It!] Test by turning ignition off and then on, select the passenger side on the adjustment switch and select reverse.

Plastic ring can be a pain to remove without an "audi special key ". I used a bot of wood and a hammer on mine 🙂

Same as last time. Take it out and have a look

More picures and details would be helpfull

Did you plug in vcds to check for faults ?

Go to bristol transmitions for diagnostics

So is there 1 missing from the bonnet ?

Bonnet stop bump buffer ...?

Vag com (vcds) Obdeleven ( android only ) Carista

You need to undo the plastic ring and take out the sender . There is a connector there that need cleaning or cutting out and solder the cables

8K0880201AE - round shape ( i belive 1 stage) 8K0880201AN - trapezoid shape ( 2 stage)

You need to plug in vcds and check what faults it has . My bet is Component Protection

Hi 🙂 1. Lemans or special edition ( audi got told off by lemans for using the name) is a trim level , its not a top spec. 2. There are mauals as well as far as i know. 3. Depending on what hardware is installed on the car ( google vcds mods a6 c6)

Its a common fault . For the record you have C6 not c5 🙂 C5 was up to 2004. And c7 is from 2011. 1. the amplituner is eaay to get on ebay. Have a look on the old one for a part number and search on ebay. The only problem would be CP . Audi have component protection on some modules to prevent theft . This needs to be removed othervise it wont work ( well it will on 1 speaker ) . This can be removed by audi or someone who has the equipment ( google for CP removal ) . Once cp is removed its just a simple swap with the old one. 2.re pipe anything will do as long as it dosent leak again !

I think new cars with MIB and MIB2 systems dont have ami as such ( seperate unit) and its built in. Standard location would be under the armrest

norm in + - 2.99 , but the 0.99 seem abit high comparing to the rest the worn seals wont show on vcsd

Exactly that ! 🙂 there was aslo 360mm for s6 and rs6

You need a tool to hammer out injectors...

Common fault are injector washers. They tick when worn . Fairly cheap to fix.